![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518514_1.jpg)
To manually solder even a small electronic board into components it will take at least 20 - 30 minutes. Now you will see how to speed up this process several times with the help of a small device that everyone can make for themselves. Using this hot solder bath, you can not only disassemble boards, but also quickly tin the contacts of parts in large quantities before assembly.
Will need
Manufacturing of equipment for tinning and desoldering
This heating element can be purchased or removed from an old multicooker.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518524_1-0-00-43-675.jpg)
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518488_1-0-00-53-615.jpg)
Inside, such an element consists of three mica plates, on the middle of which a nichrome wire is wound.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518503_1-0-01-22-450.jpg)
There is no need to disassemble it as shown in the photo. Just make sure that the permissible network voltage of 220-240 V is written on its body.
Take a tin can and cut it lengthwise with metal scissors.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518518_1-0-02-05-622.jpg)
From the resulting strip, bend the contour according to the size of the heating element.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518515_1-0-02-33-186.jpg)
We make square cuts on the sides and fold them over.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518473_1-0-03-04-823.jpg)
Install the heater and bend the sides.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518528_1-0-03-12-192.jpg)
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518529_1-0-03-27-750.jpg)
It turned out to be a small bath.
Next, we cut out a small rectangle from a thick board.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518555_1-0-03-39-414.jpg)
We drill holes in it for the output of the element.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518564_1-0-03-58-545.jpg)
On the reverse side we connect them through a switch to a wire with a power plug.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518509_1-0-04-19-925.jpg)
Insulate with tape from below.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518484_1-0-04-29-735.jpg)
We screw the bathtub on top with self-tapping screws.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518538_1-0-04-44-374.jpg)
Turn it on and start filling it with solder.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518530_1-0-05-06-074.jpg)
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518514_1-0-05-24-057.jpg)
We remove the scale from above with a screwdriver.
Now you can immerse the board into the bath with the bottom contacts, holding it with some pliers, and quickly pull out the parts with the other.
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518516_1-0-05-27-620.jpg)
A couple of minutes and you're done!
![How to make a device for quickly desoldering circuit boards](https://i.washerhouse.com/uploads/posts/2020-03/1584518485_1-0-05-44-810.jpg)
Adviсe
- Do not touch the bathtub during operation.
- Be very careful: molten metal is very dangerous.
- Don't make the bath very deep.