![Wedding glass](https://i.washerhouse.com/images/7/2351-svadebnyy-bokal.jpg)
You will need a piece of tulle or other mesh fabric. Size 20 cm by 40 cm. For decoration you need pink rhinestones and a center for a flower. The flower itself is created from ribbon, it takes approximately 7 pieces of 4 cm each, for a total of about 30 cm of satin soft pink ribbon, the width of which is 4 cm. For the side branches, look for two white pieces of 4 by 4 cm and two pink ones. Use glue to secure everything to the glass. A glue gun is ideal because its glue resembles transparent plastic, holds the material well and does not have a bad odor.
Let's start creating seven petals for the main flower. To do this, we cut the pink ribbon into blanks, that is, 4 by 4 cm squares. We bend the square as in the figure.
![bend the square](https://i.washerhouse.com/images/7/2339-eregibaem-kvadrat.jpg)
Then we bend the workpiece again so that we get a triangle.
![bend the square](https://i.washerhouse.com/images/7/2340-eregibaem-kvadrat.jpg)
Now you need to bend the work evenly.Try to make a sharp, beautiful angle, don’t rush, and then everything will work out! Fix all layers with tweezers.
![bend the square](https://i.washerhouse.com/images/7/2341-eregibaem-kvadrat.jpg)
To create an inverted petal, it is necessary to trim the base of the workpiece in such a way that when bent, it can be fixed and not bend back. Use scissors not to cut parallel to the base, but at an acute angle.
![cut off](https://i.washerhouse.com/images/7/2342-obrezaem.jpg)
Burn the base of the petal with a lighter, this action will fuse all the layers together and you will get a petal for the flower.
![melt](https://i.washerhouse.com/images/7/2343-oplavlyaem.jpg)
Turn the petal out, if the base (the part closer to the middle) is sticking out a lot, then trim it.
![petal](https://i.washerhouse.com/images/7/2344-lepestok.jpg)
Cut a circle with a diameter of 1-1.5 cm from the tape and glue 7 identical pink petals onto it.
![flower](https://i.washerhouse.com/images/7/2345-cvetok.jpg)
To decorate the middle of the flower, a large rhinestone or the top of a hairpin, which is used to decorate wedding hairstyles, is suitable. If you have one of these lying around, then its “hat” will be the best flower center. Prepare a piece of ribbon and tulle to create a “skirt” around the wedding glass.
![for decorating wedding hairstyles](https://i.washerhouse.com/images/7/2346-dlya-ukrasheniya-svadebnyh-prichesok.jpg)
Glue this piece to the place where the stem of the glass meets the base; it is more convenient to attach the “skirt” to the tape. If you glue it to a glass, there is a high probability that the mesh will simply fall off the glass.
![for decorating wedding hairstyles](https://i.washerhouse.com/images/7/2347-dlya-ukrasheniya-svadebnyh-prichesok.jpg)
Bend the material almost in half, retreating 1-2 cm from the bottom edge. This is necessary so that the skirt has 2 tiers and appears fuller. Sew the mesh with large stitches, constantly tightening the thread.
![for decorating wedding hairstyles](https://i.washerhouse.com/images/7/2348-dlya-ukrasheniya-svadebnyh-prichesok.jpg)
You should get something like this full skirt.
![glasses in the base](https://i.washerhouse.com/images/7/2349-bokala-v-osnovanie.jpg)
Glue the skirt around the leg. Be sure to glue the joint, otherwise everything will stick out in different directions.
![glasses in the base](https://i.washerhouse.com/images/7/2350-bokala-v-osnovanie.jpg)
Now we glue the flower in the middle of the glass. Make branches of white and pink petals symmetrically to the flower. All empty space can be decorated with rhinestones.Be sure to cover the place where the skirt is glued with a pink ribbon, tie a bow and also randomly decorate the entire skirt with pink rhinestones. The glass for the newlyweds is ready.
![Wedding glass](https://i.washerhouse.com/images/7/2352-svadebnyy-bokal.jpg)